![sinano ac servo driver sinano ac servo driver](https://marineindustrialmachinery.com/images/product/sinano-e50c-mb202b27f-ac-servo-driver-ad-series-4945614311550052557.jpg)
- SINANO AC SERVO DRIVER INSTALL
- SINANO AC SERVO DRIVER DRIVERS
- SINANO AC SERVO DRIVER DRIVER
- SINANO AC SERVO DRIVER SERIES
- SINANO AC SERVO DRIVER FREE
We give free estimates and offer a year warranty. Quickly Hire our Service Dept to do the work for you! Credit Application Form If you need your Sinano unit tested or repaired then give us a call at 1-33. Recent 250 of 15374 Units Cybelec CPU1201 Circuit Board Accurpress PLC5.3 Circuit Board Intel FI-PNTHI-HRC01/6 Control Unit Emerson M7012 Radio.
SINANO AC SERVO DRIVER INSTALL
Alert y Install the fan if the temperature around. Y The output of Servo drive must NOT touch the AC power. Y Circuit & change components between entering shutting down the power supply and stopping showing CHARGE LED light of the Servo driver. I Warning and Alert: Warning y Do not proceed to the assembly of the line while electrifying.
SINANO AC SERVO DRIVER SERIES
Current thread: Need to get your Sinano Repaired?ĪC Servo System TSTE Series Simplified Manual.
SINANO AC SERVO DRIVER DRIVER
Servo driver is OFF if Emergency Stop (D/I) is ON.Need to know the wiring configuration of Sinano Servo Drive DOPC016B for machine trouble shooting, please provide the manual for above model. (If over-travel is occurred, the servo power may be disabled or put on hold.) Maintain at lease 2 cm spacing around the Driver unit.ĭuring and after installation, any foreign object such as cutting chips, small screw, or washer which may fall into the opening of the Driver unit must be prevented. Use four (4) M5 screws to mount the Driver securely. (5) If a line filter is not allowed for the reason of excess leakage current, then a insulating transformer is required at the input of the Driver. (4) If there is a big magnet switch or welding equipment, which may generate electronic noise, near the Driver installation, then a line filter is required.įor single-phase power source: DELTA 06DPCW5įor three-phase power source: DELTA 08TDS4W4 Insulation from water, water mist, or cutting fluid is required. (3) The Driver shall not be installed in an environment where corrosive gases, excess dust, or metal power is present. (2) Use rubber pad or shock absorber to insulate vibration if there is vibrating equipment nearby. (1) If installed in a confined chassis, please provide necessary ventilation system to maintain the environmental temperature of the Driver below 55℃. The machine, which the Driver and motor are installed must be single-point grounded. To prevent electric leakage, connect the motor ground to the FG terminal of theĭriver and connect this FG to Class 3 grounding. Disconnect the power if the Driver/Motor unit is not used for a prolonged period.Ĥ. While power on the Driver and/or motor, stand clear from the unit to prevent personal injury caused from erroneous operation.ģ. If it is necessary to touch the terminal or open the driver chassis, please wait at least 10 minutes before continuing.Ģ. Many high volume capacitors are used in the Driver circuit these capacitors remain charged even if the unit power is been shut off. Please use the original packaging for driver relocation and handle with care.ġ. No damage to the packaging material occurred during transportation. (Please see the Driver Specification for correct driver.)ģ. The capacity of the driver matches with the motor to be driven. The motor (s) and driver(s) are the same as ordered.Ģ. Procedures for Panel Operation are described in Chapter 3.įinally, the Alarm Codes are given in Chapter 4.Īfter receiving the shipment from your supplier, please verify the following:ġ.
![sinano ac servo driver sinano ac servo driver](https://img.mweb.com.tw/thumb/576/1000x1000/%E7%94%A2%E5%93%81%E4%B8%8A%E5%82%B3/M%E9%96%8B%E9%A0%AD/MOTOR%E9%A6%AC%E9%81%94/sinano-ac-servo-motor-6cc401g3debeas-02_1.jpg)
Wiring information is shown in Chapter 2. In this manual, the installation related information such as Dimensions and Specifications are described in Chapter 1. This manual is intended for use by vendors who are responsible for installing and setting up TSDA series Driver consequently, it assumes a basic working knowledge of This manual provides the information you need to install and configure TSDA seriesĭriver. It is highly recommended that the user is familiar with this manual and performs all setup and operations with caution. However, erroneous operation may result in unpredictable accident and cause damage to the Driver or severe personal injury. Many safety related features have been built in theĭriver design.
SINANO AC SERVO DRIVER DRIVERS
TSDA series Drivers use the latest servo technology to provide high-precision and versatile functions for driving TEDĬB,MB and CC series servo motors. Thank you for choosing TSDA series AC servo Drivers. Historical alarm code.24Ĭlear the historical alarm codes.